The SCHUNK Co-act EGP-C is an electric two-finger parallel gripper for handling small and medium-sized workpieces in assembly, part transfer, and machine tool loading. It combines integrated current limitation, a collision protection cover, and position sensors. For compatible DOBOT CRA, Nova, and CRH robots, the DOBOT+ plug-in provides I/O configuration, gripper commands, and position-signal monitoring within DobotStudio Pro. Gripping force is adjusted manually on the gripper to suit the workpiece and application.
DGUV-Certified Gripping Unit
Integrated current limitation and a collision protection cover support collaborative handling. DGUV certification applies to the gripping unit; the complete robot application requires its own assessment.
Manually Adjustable Gripping Force
An integrated rotary switch provides four gripping force settings: 25%, 50%, 75%, and 100%. Force selection takes place directly on the gripper.
Integrated Position Monitoring
Two inductive proximity switches monitor configured jaw positions. Sensor adjustment allows the feedback signals to be matched to the selected gripping setup.
DOBOT+ Control and Programming
The dedicated plug-in supports I/O configuration, opening, closing, stopping, error acknowledgement, and position-signal reading, with corresponding block and script programming functions.
Pick and Place
Transfers small and medium-sized workpieces between defined pickup and placement positions within the selected gripper’s stroke and load limits.
Assembly and Part Positioning
Grips and positions components for assembly operations, with manually selected gripping force and sensor feedback matched to the workpiece.
Machine Tool Loading
Handles workpieces during machine loading and unloading where the operating environment meets the gripper’s specified temperature and protection requirements.
The following data describes SCHUNK’s current Co-act EGP-C 40 and 64 sizes. Mounting interfaces, cabling, dimensions, and weight vary by ordering configuration.
| Parameter | Co-act EGP-C 40 | Co-act EGP-C 64 |
|---|---|---|
| Gripper type | Electric two-finger parallel gripper | Electric two-finger parallel gripper |
| Stroke per jaw | 6 mm | 10 mm |
| Minimum / maximum gripping force¹ | 35 / 140 N | 65 / 230 N |
| Recommended workpiece weight² | 0.7 kg | 1.15 kg |
| Maximum permissible finger length | 50 mm | 80 mm |
| Repeat accuracy | 0.02 mm | 0.02 mm |
| Closing / opening time³ | 0.2 / 0.2 s | 0.49 / 0.49 s |
| Drive | Brushless DC servomotor | Brushless DC servomotor |
| Nominal supply voltage | 24 VDC | 24 VDC |
| Supply voltage range | 21.6–26.4 VDC | 21.6–26.4 VDC |
| Control interface | Digital I/O | Digital I/O |
| Gripping force adjustment | Manual rotary switch: 25%, 50%, 75%, 100% | Manual rotary switch: 25%, 50%, 75%, 100% |
| Protection class | Mechanical: IP30; electrical: IP40 | Mechanical: IP30; electrical: IP40 |
| Ambient operating temperature | +5 to +55 °C | +5 to +55 °C |
¹ Gripping force is the sum of the forces applied by both jaws at SCHUNK’s specified reference distance. Available force depends on finger length.
² Recommended workpiece weights assume a coefficient of static friction of 0.1 and a safety factor of 2 against slipping under gravity.
³ Times describe base-jaw movement without application-specific fingers and exclude PLC response time.
| Parameter | Requirement |
|---|---|
| Compatible DOBOT robots | CRA series, Nova series, CRH series |
| CRA series minimum software | DobotStudio Pro V4.6.7.0-stable or later |
| Nova series minimum software | DobotStudio Pro V4.6.7.0-stable or later |
| CRH series minimum software | DobotStudio Pro V4.7.3.1-stable or later |
Plug-in: SchunkEGP_v1-0-0-stable
Plug-in download: SCHUNK Co-act EGP-C DOBOT+ Plug-in
Hardware installation and operation: SCHUNK Co-act EGP-C Assembly and Operating Manual
Become a Dobot+ member to accelerate automation transformation in the world. Together we can maximize the impact of our products.
Take part in automation transformation. Let’s work together towards a more efficient tomorrow.